Torsion Spring Part Number System - In Inches
StockSpringsCatalog.com Part Number System For Torsion Springs in Inches
P
Part Number
T
Torsion Spring
023
Wire Diameter
-251
Outer Diameter of Spring
-7750
Total Coils
-MW
Material Type
-RH
Wind Direction
-1000
Leg Lengths
-N
Finish
-IN
Unit of Measure
Our Part Numbers Have Changed
Since we have created the new website, we have updated our dimensional part numbers to not have any decimal points. However, we have kept the three decimal spaces so remember to add the extra zeros where needed.
Previous Part Number
PT023-251-7.750-MW-RH-1.000-N-IN
New Part Number
PT023-251-7750-MW-RH-1000-N-IN
StockSpringsCatalog.com By Acxess Spring Part Number System In Inches For Torsion Springs
We have developed an easy stock spring part number system using the actual dimensions of the spring. This part number system for springs was developed to facilitate the creation and understanding of part numbers for springs. By using the actual dimensions of the spring in the spring part number we have made our part numbers for springs simple, but yet descriptive of the actual spring measurements in real time. Our part numbers consist of a series of numbers to describe each individual spring. Each part number is separated by hyphens to indicate different dimensional characteristics of a spring. Each series describes a different dimension. Below you will find a breakdown explanation of how StockSpringsCatalog.com part number system works for torsion springs in inches.
- The letter P stands for Part Number
- The letter T stands for Torsion Spring
- The first series of numbers indicates Wire Diameter=WD
- The second series, following the first hyphen, indicates Outer Diameter=OD
- The third series, following the second hyphen, indicates Total Coils=TC
- The fourth series, following the third hyphen, indicates Material Type
- The fifth series, following the fourth hyphen, indicates Direction of Wind
- The sixth series, following the fifth hyphen, indicates Leg Lengths
- The seventh series, following the sixth hyphen, indicates Finish
- The eighth series, following the last hyphen, indicates Unit of Measure Inches=IN
Please look at the part number example below for a further explanation.
Torsion Spring Part Number Example In Inches:
PT023-251-7750-MW-RH-1000-N-IN
- P=Part Number
- T=Torsion Spring
- 023=0.023 Wire Diameter=WD
- 251=0.251 Outer Diameter=OD
- 7.750=Total Coils=TC
- MW=Material Type
- RH=Wind Direction
- 1.000=Leg Lengths=LL
- N=Finish
- IN=Unit Of Measure Inches
Nomenclature:
Material Type: BC=Beryllium Copper, HD=Hard Drawn, MW=Music Wire, OT=Oil Tempered, PB=Phosphor Bronze, SPR=Spring Steel, SST=Stainless Steel
Wind Direction: LH=Left Hand, RH=Right Hand
Leg Lengths=LL
Finish: GI=Gold Irridite, N=None, Z=Zinc
Unit of Measurement: IN=inches, MM=millimeters
StockSpringsCatalog.com By Acxess Spring Part Number System In Metric Millimeter For Torsion Springs.
P
Part Number
T
Torsion Spring
023
Wire Diameter
-251
Outer Diameter of Spring
-7750
Total Coils
-MW
Material Type
-RH
Wind Direction
-1000
Leg Lengths
-N
Finish
-IN
Unit of Measure
Our Part Numbers Have Changed
Since we have created the new website, we have updated our dimensional part numbers to not have any decimal points. However, we have kept the three decimal spaces so remember to add the extra zeros where needed.
Previous Part Number
PT023-251-7.750-MW-RH-1.000-N-IN
New Part Number
PT023-251-7750-MW-RH-1000-N-IN
StockSpringsCatalog.com By Acxess Spring Part Number System In Inches For Torsion Springs
We have developed an easy stock spring part number system using the actual dimensions of the spring. This part number system for springs was developed to facilitate the creation and understanding of part numbers for springs. By using the actual dimensions of the spring in the spring part number we have made our part numbers for springs simple, but yet descriptive of the actual spring measurements in real time. Our part numbers consist of a series of numbers to describe each individual spring. Each part number is separated by hyphens to indicate different dimensional characteristics of a spring. Each series describes a different dimension. Below you will find a breakdown explanation of how StockSpringsCatalog.com part number system works for torsion springs in inches.
- The letter P stands for Part Number
- The letter T stands for Torsion Spring
- The first series of numbers indicates Wire Diameter=WD
- The second series, following the first hyphen, indicates Outer Diameter=OD
- The third series, following the second hyphen, indicates Total Coils=TC
- The fourth series, following the third hyphen, indicates Material Type
- The fifth series, following the fourth hyphen, indicates Direction of Wind
- The sixth series, following the fifth hyphen, indicates Leg Lengths
- The seventh series, following the sixth hyphen, indicates Finish
- The eighth series, following the last hyphen, indicates Unit of Measure Inches=IN
Please look at the part number example below for a further explanation.
Torsion Spring Part Number Example In Inches:
PT023-251-7750-MW-RH-1000-N-IN
- P=Part Number
- T=Torsion Spring
- 023=0.023 Wire Diameter=WD
- 251=0.251 Outer Diameter=OD
- 7.750=Total Coils=TC
- MW=Material Type
- RH=Wind Direction
- 1.000=Leg Lengths=LL
- N=Finish
- IN=Unit Of Measure Inches
Nomenclature:
Material Type: BC=Beryllium Copper, HD=Hard Drawn, MW=Music Wire, OT=Oil Tempered, PB=Phosphor Bronze, SPR=Spring Steel, SST=Stainless Steel
Wind Direction: LH=Left Hand, RH=Right Hand
Leg Lengths=LL
Finish: GI=Gold Irridite, N=None, Z=Zinc
Unit of Measurement: IN=inches, MM=millimeters