Attention! Input results shown will be +/- 10% from middle value. Hint: The closer your min and max inputs are, the more accurate your results will be!

Attention! Input results shown will be +/- 10% from middle value. Hint: The closer your min and max inputs are, the more accurate your results will be!

Attention! Input results shown will be +/- 10% from middle value. Hint: The closer your min and max inputs are, the more accurate your results will be!

Attention! Input results shown will be +/- 10% from middle value. Hint: The closer your min and max inputs are, the more accurate your results will be!

Torsion Spring Part Number System - In Metric Millimeter

StockSpringsCatalog.com Part Number System For Torsion Springs in Metric Millimeter

P

Part Number

T

Torsion Spring

1500

Wire Diameter

-17300

Outer Diameter of Spring

-6000

Total Coils

-MW

Material Type

-LH

Wind Direction

-51000

Leg Lengths

-N

Finish

-MM

Unit of Measure

Our Part Numbers Have Changed

Since we have created the new website, we have updated our dimensional part numbers to not have any decimal points. However, we have kept the three decimal spaces so remember to add the extra zeros where needed.

Previous Part Number

PT1500-17300-6.000-MW-LH-51.000-N-MM

New Part Number

PT1500-17300-6000-MW-LH-51000-N-MM

StockSpringsCatalog.com By Acxess Spring Part Number System In Metric Millimeter For Torsion Springs

We have developed an easy stock spring part number system using the actual dimensions of the spring. This part number system for springs was developed to facilitate the creation and understanding of part numbers for springs. By using the actual dimensions of the spring in the spring part number we have made our part numbers for springs simple, but yet descriptive of the actual spring measurements in real time. Our part numbers consist of a series of numbers to describe each individual spring. Each part number is separated by hyphens to indicate different dimensional characteristics of a spring. Each series describes a different dimension. Below you will find a breakdown explanation of how StockSpringsCatalog.com part number system works for torsion springs in metric millimeter.

  • The letter P stands for Part Number
  • The letter T stands for Torsion Spring
  • The first series of numbers indicates Wire Diameter=WD
  • The second series, following the first hyphen, indicates Outer Diameter=OD
  • The third series, following the second hyphen, indicates Total Coils=TC
  • The fourth series, following the third hyphen, indicates Material Type
  • The fifth series, following the fourth hyphen, indicates Direction of Wind
  • The sixth series, following the fifth hyphen, indicates Leg Lengths=LL
  • The seventh series, following the sixth hyphen, indicates Finish
  • The eighth series, following the last hyphen, indicates Unit of Measure Metric Millimeter=MM

Please look at the part number example below for a further explanation.

Torsion Spring Part Number Example In Metric Millimeter:

PT1500-17300-6000-MW-LH-51000-N-MM

  • P=Part Number
  • T=Torsion Spring
  • 1500=1.500 Wire Diameter=WD
  • 17300=17.300 Outer Diameter=OD
  • 6.000=Total Coils=TC
  • MW=Material Type
  • LH=Wind Direction
  • 51.000=Leg Lenghts=LL
  • N=Finish
  • MM=Unit Of Measure Metric Millimeter

Nomenclature:

Material Type: BC=Beryllium Copper, HD=Hard Drawn, MW=Music Wire, OT=Oil Tempered, PB=Phosphor Bronze, SPR=Spring Steel, SST=Stainless Steel

Wind Direction: LH=Left Hand, RH=Right Hand

Leg Lengths=LL

FinishGI=Gold Irridite, N=None, Z=Zinc

Unit of Measurement: MM=millimeters, IN=inches

StockSpringsCatalog.com By Acxess Spring Part Number System In Inches For Torsion Springs.